Perfect fit for Ender3 Pro, great enclosure for the price!

J.F. · December 20, 2025

I've been meaning to get an enclosure for ages, as my printer sits near an HVAC vent and I know that doesn't help prints. Temps vary wildly in the basement too, and I'm sure that isn't helping. Finally pulled the trigger on this enclosure. The medium size is HUGE and has more than enough room for my Ender3 Pro.Assembly was straightforward, and didn't take too much effort. Directions were good. Just make sure you fully seat all of the rods into their sockets and you shouldn't have any issues. I found it easy to assemble the frame and set it on the floor, then slide the the cover over the frame, versus the directions saying to try to drop the frame into the loose cover. It's a snug fit, but it went on with no problem. I was able to zip-tie my webcam to the frame, so it didn't need to sit on the stand that I printed for it anymore, which is a nice space saver.I need to clean up some wires and make things look nice inside, but it's a great enclosure that should help me get more clean and consistent prints. It also cut the fan and printer noise way down, which is great!My only small complaint would be the light bar - it puts out enough light in there to work, but I feel like no matter where I've tried to move it, it's just not quite right with my webcam and Klipper. I see they sell additional lights, so I may buy one, or just design and print some other kind of solution. Other than that one small thing, which isn't worth knocking the product, as it's a personal preference, this enclosure rocks!

A GREAT value for a surprisingly effective enclosure!

M.M. · November 30, 2024

I needed to reliably print a few parts for a Voron 2.4 build, which requires ABS. I have an old Prusa I3 clone in the garage which I've occasionally used for this since there are usually no drafts, and I stink up the garage instead of the house. During the hot summer months, when the garage is often pushing 90F, I'm normally able to get away with printing ABS well with an open frame. Come fall and winter, warping becomes an issue. Plus, the family was getting tired of the "Don't open the garage door!" exclamations from me when I was printing ABS.Picked this up to provide a quick enclosure, with hopes it would allow reliable ABS printing (and allow the garage door to be opened while doing so). This has worked SHOCKINGLY well. Since my printer has been in this enclosure, I've been able to print about 10 parts, a few of which are highly prone to warping (small contact space on the bed). All of them have printed successfully and beautifully. Of course, the blast of "ABS stink" when you unzip it to remove the print is fun."Just the facts, ma'am":Pros:- Super easy to assemble, although it's bigger than you think so have some space.- Canvas with the shiny fireproof lining is thick and well sewed. It didn't feel "cheap" at all. There is quality here.- I find the LED to be plenty of illumination, especially since it reflects off the shiny material inside. My print camera finds it to be plenty of light, too.- A good number of round bungs to route cables through, that seem to be in the right place. Two on the back and one on the right-hand side towards the rear.- Has a rather large flap on the left, which I'm not using. Closes with velcro.- I like that measurements were listed clearly, so I could ensure it would fit and get the correct size. Medium worked for my Prusa I3 clone (about the size of an Ender 3, I guess) with room to spare.- I can print ABS consistently, and get strong, clean prints!Cons:- Bungs are a little on the tight side. Had to really push the power cable through and thought I was going to tear the fabric. I did not, which is also a pro I guess, that canvas is pretty tough!- The clear viewing window has a lot of folds in it, so it can be a little difficult to see print details.Overall, I think this is a fantastic value if you're looking for an inexpensive and plug-and-play enclosure for your 3D printer.

Works great. Fits A8. Delivered late.

M.L.S. · February 11, 2026

The media could not be loaded. This is great and fits my Anet A8 with room to spare. You cannot go wrong for the price. It keeps the print warmer with no drafts and knocks the noise down a little. The LED strip could be brighter and does not include a USB power adapter but it's fine for this price. Easy to build and even includes latex gloves to handle the fiberglass rods.As for Bolo, 3 of our last 5 packages have been late, including this one. A couple of those were weather delays but not this time. Step it up, Jeff.

Good enclosure but previously opened

T.R. · November 8, 2025

The enclosure had been opened prior to me receiving it. The package it came in was a makeshift box from a previous box. I'm guessing it was a returned item. I almost returned it because of that. The enclosure itself does a nice job holding in the heat and the large zipper flap made it easy to put the printer (Prusa MK3S+) into the enclosure. The light is a nice feature as well. It's a good enclosure for the price.

Very good quality and useful size

E.B. · September 14, 2023

Assembly was very easy. It all snapped together and made sense. The fabric fits over the frame without being too tight that it's a pain, but definitely is tight enough to stay in place. The quality is very good and better than I'd expected to be able to get for this price point. The zipper flap going all the way to the back is awesome for easy access to the printer. I have my printer on slightly higher feet but it still fits properly in the enclosure, though if you have the Extender or taller height you will want the bigger size.The included light bar is a huge addition, I get really good quality videos from my mounted camera and I don't need to light the whole room to do so.I have only printed PLA+ so far but I'm looking forward to printing Nylon, ABS and other materials that want an enclosure. The sound reduction isn't a huge factor but it does a bit for that as well. My printer was already fairly quiet and this made it very nice. The small door on the side will be useful if I decide to do some type of ventilation, especially for lasering. I'm looking forward to getting a lot more use out of this and I may try and figure out a way to print directly from my dryer while still being mostly enclosed. I believe there may be enough space in the enclosure for that.