This camera has AHD1080P high-definition picture quality, 170-degree ultra-wide angle, and excellent night vision, which can maintain clear pictures even in low-light environments.

• We offer replacements for defective products. If you have any other questions, please send a message directly to the after-sales address on the manual.
• The housing of the reversing camera can be rotated 360° so that installation is not restricted!
• 45° adjustable rear camera, the adjustment of the angle is no longer dependent on the seals, the rear view camera can be partially rotated through the lens to find the best view!
• The reverse camera cable uses an integrated step-down module, low power consumption and no more worries about heat!
• Double-layer shielded cables ensure more stable video signal transmission with less interference and delay.
• The angle of the car reversing camera has been extended from 140° to 170° to cover more blind spots.
• The rear view camera is made of a durable alloy and a nano-infusion process that further improves waterproofness! In case of water intrusion, we will provide you with a brand new replacement camera.
• Supports 12-24V, suitable for all vehicles!

This is a universal backup camera for monitors with an RCA connector. (Navigation system/radio/head unit/monitor is referred to as monitor in the text)

​Notes:

​*This Jansite backup camera is perfect for REAR,FRONT and SIDE VIEW. (Monitor/LCD/Screen/Display/Radio not included).

​* Mount the camera on the panel and route the wire to inside (DO NOT pinch the wire/cable when route the wire, pinched wire will damage the camera).

​* Apply electrical tape for the joint of the red power wires and RCA wires, and use zip ties to fasten the wire on your vehicle.

​​​* If your head unit is an Android monitor with a reverse triggering wire, please find it, and connect it with the extension wire's triggering wire wel (small short wire next to the RCA/AV connector).

​​​​​​​​​​​* Before you routing, if there is no image on the screen, other than check the camera, please check display setting as well(Only Support AHD1080P 25fps or CVBS). You can use other device with RCA connector to check if the camera works.

* If the camera Angle is loose, it may be that the screw fixing the lens is too short, we will replace the screw within 24h (after-sales service address - user manual)

There are 2 kinds of back covers for this reversing camera, which are no-drill back cover and bolt-on back cover.

NOTE: All of our 4-pin car rear view cameras cannot be directly connected to the dash cam/mirror dash cam/GPS.

Common Problems:

1.If the screen suddenly turns black/blue when reversing, showing no signal, etc., please contact the after-sales address on the manual, we will re-send a rectifier, which can solve the above problems.

2.If the screen flashes, no image, etc., it may be the signal setting is incorrect, please contac the after-sales address on the manual, we have a signal setting video for reference.

3.If the camera suddenly stops working: 1. Check if the power cord is loose; 2. Check if the car voltage has dropped;

Our rear view camera defaults to rear camera, you can cut the white wire to use as a front camera.

3 control modes: Orange line: CVBS-N switching to AHD 1080P fps (But if your monitor is CVBS 720P, then the image quality may be a little bit worse)（If you have an AHD720 or PAL monitor, then this rear camera is not suitable); White line: Switch to front/rear view ; Green line: Switching with/without reversal of the guide line

The reason why the device cannot be displayed:

1, please check whether your wiring is correct: whether the red part of the rear camera is connected to the reverse light "+"

2, The camera default setting is CVBS. Enter the device to change the video format to CVBS-NTSC.

3. If the display supports AHD 1080P: 1. Please set the video format to AHD 1080P 25 fps. 2. Cut the orange coil of the camera. 3. Restart the device again.

4. If your head unit is an Android monitor with a reverse triggering wire, please find it, and connect it with the extension wire's triggering wire wel (small short wire next to the RCA/AV connector).

If there is any confusion about the cutting method of the Jaster reversing camera, please contac our after-sales service（On the product manual）

This reverse camera for car has a 170° ultra-wide viewing angle, effectively reducing blind spots in your field of vision.

What kind of centre screen is suitable? --- Must be retrofitted Android screen √ (original screen x)

Continuous Upgraded 1080P AHD Backup Camera:

Please note: this camera is designed for short-time reversing use only, not for continuous power-on monitoring.

Before cutting the orange wire loop, Please make sure your display supports AHD signal. If not, you can only use CVBS.

Supports DC 12V power only. Do not connect to systems above 12V (e.g., trucks or RVs) unless a step-down converter is used.

Please set video format on the radio: CVBS-N or AHD 1080P 25fps!

How to know if the device supports AHD1080P camera？

Go to Car Settings >> Factory Settings >> Reverse (Picture) Settings >> Select NTSC or AHD1080P 25fps.

What should I do if my device does not support 1080P?

1. The video format needs to be set to CVBS-NTSC.

2. Keep the orange wire.

Some cars because the voltage is unstable, if the screen suddenly turns black when reversing, showing no signal, etc., please contact the after-sales address in the manual, we will re-send a rectifier, can solve the above problems

What devices does the backup camera fit?

This camera has a RCA connector, it is suitable for the car original screen with RCA connector or other monitor with RCA connector.

It doesn't fit dash cam、mirror cam、GPS and car recorder.