5.0 out of 5 stars Great colour filament

B.p. · 2 August 2025

Straight out of the packaging I thought it was going to be tangled as the end wasn't secured. Done 4 large pass through middles and had no tangles, the colour is great and it was easy to print with.Very little stringing so I may need to dry it out a little but overall im impressed with filament.

5.0 out of 5 stars Nice clean prints with no problems.

D.A.J. · 23 August 2021

Product arrived well packaged and sealed with the normal silica gel packet inside.Comes with a grip seal bag to store the reel in should you not use the product for some time after opening. I don't normally have issues with that but it was a nice touch to have the bag supplied in case I required it.Inspection of the windings onto the reel looked excellent, so no worries about any tangling causing issues during the prints. I have purchased PETG from this company previously and that came perfectly wound too so good to know you can trust the filament to flow freely from the spool.Played around with temps, the PLA seemed to give the best results around 190 degrees, no sign of any excessive stringing and good clean.Did some normal speed purging and the material flowed well, nice and even purging with no spitting or other issues.First print was the Olaf model.Printed at default speed on Geeetech A20, first layer adhesion was perfect on the Geeetech standard mylar sheet that comes with the printer. The purge line peeled off cleanly once cooled.The model was printed with 10% infill, the external finish was very impressive, I did part way through increase speeds by 25% and no issues were noted regarding the filament feeding through the nozzle. I have had some PLA that didn't work well at higher speeds, this seemed to cope without problems.Second print was the penguin, no infill, three outer layers, three layers top and bottom, on the same A20 printer. A few lines in the lower part of the body, but that was down to the printer itself and not the filament, the filament performed perfectly well on this print also. A very nice smooth and tactile finish on both models.Finally I decided to test it further by printing a lithophane of the Astronaut on the moon.I have had some PLA that did not print this so well, partial lines missing etc.. As you can see from the photograph it gave a great result.I have previously purchased PLA from other companies, at higher prices than this. This has performed perfectly so far, so will be my filament of choice for the future.

5.0 out of 5 stars Easy to print

D. · 17 May 2025

It's nice and transparentish once printed, I'm sure it can be improves so it's user error.Would love it as a lamp diffuser or similarGood quality print direct from unboxing without a dryer

4.0 out of 5 stars Trees are brown

M. · 19 March 2025

Nice filament, quality is fine, prints OK.I chose it for the novelty value of being 'wood' coloured hoping for some texture or interest.'Brown' or 'beige' would be more accurate. So probably won't risk the others in the range such as marble, etc.

5.0 out of 5 stars Great Looking and Workable Filament

C.J. · 1 May 2022

Super fast delivery of this filament, Item arrived very well packaged and upon opening I noticed that it even includes a re sealable bag for storage after use. (nice little addition) although I may not use it as I store all my filaments in air tight storage containers.I decided to go all in and opted straight away for a full print of an articulated model using previously used settings for other filaments to see what the results where. I didn't bother with any temp test towers, I just wanted to see what it does straight out of the package.I saved a random model onto the SD card with the temps set at 200 for the Hotend and 55 for the Bed. I put the SD card into my Ender 5 Pro and started the print, albeit a little late at 9pm, I checked on the print and took a photo approx. 2 hours into it and all was looking good. I felt confident with the print at this point so decided to leave it running over night and woke up in the morning to a shiny new articulated shark to add to my ever growing collection of random models.The overall finish was really good, quite smooth and clean with no stringing present at all and no abnormalities or curling from the heated bed.The colour of the filament (Model) in natural light really is fantastic, I like the sheen to this filament and am sure it will be used more and more by me and I will definitely be purchasing this product again in the very near future.All in all a great product that works really well for what I did using the above settings.Highly recommended.

1.0 out of 5 stars Snaps constantly and is tangled on the spool

M. · 9 June 2023

Never had a filament that breaks so much. I purchased two reals of this but will never buy GiantArm again - this is terrible.The reel appears to have sections that are simply very brittle. So it'll be fine for a bit then go through a brittle section that just snaps constantly. Use a different clear PLA and haven't had a single issue. When I slowly unroll the filament I can snap it cleanly with my hands for a big, then the next section is bendy and very resistent to breaking, carry on and you get to another brittle section. This isn't a settings issue, the filament is snapping inside the PTFE tubing! This is the same on both reels.I also had multiple instances of the filament pooly aligned on the spool resulting in it jamming because the filament snagged on itself on the spool.End prints look good, it just is a ton of hassle to use because it fails so often. I'll be using a different brand from now on. Probably one of the worst filaments I've purchased.

5.0 out of 5 stars Great Performance Filament

A. · 23 February 2025

I was a little sceptical about using this as I hadn't heard of the brand before. I can say the filament is excellent and prints great using an Ender 3 clone 3d printer. I use 210degC nozzle temp with 60degC bed temp PEI build plate and have no adhesion problems. The bag it comes in is resealable and comes with silica gel to keep it dry in storage.

5.0 out of 5 stars Nice colour

L. · 15 April 2025

Nice colour, not all companies do brown. Really easy to print with no adhesion issues, stringing issues or tangles, nor did I need to dry before hand.Highly recommended

Muy buena opción para impresión general

A.S. · 7 July 2025

Envío muy rápido. Llegó a la mañana siguiente de pedirlo. Este filamento PLA transparente es una excelente opción si buscas un equilibrio entre precio y calidad aceptable para tus impresiones 3D. Es una solución ideal para proyectos donde la visibilidad interna o un acabado traslúcido son clave, como prototipos, modelos conceptuales o piezas decorativas.La relación calidad-precio es uno de sus puntos fuertes. No es el filamento más premium del mercado, pero lo que ofrece por su coste lo convierte en una compra inteligente. Las impresiones resultantes tienen una calidad más que aceptable, con buena adherencia entre capas y una extrusión consistente que minimiza problemas comunes. Si bien podrías encontrar ligeras variaciones en la transparencia o el brillo en comparación con opciones de gama alta, para la mayoría de los usuarios y aplicaciones, el rendimiento es notablemente bueno.En resumen, si buscas un filamento PLA transparente económico y que cumpla con las expectativas para tus necesidades de impresión 3D diarias, esta bobina es una opción muy recomendable.

Correspond parfaitement !

L.A. · 30 June 2022

PLA au top, le rendu est bien, le mat change vraiment du plastique brillant !C’est sûrement un mélange bois avec, il faut voir ! Mais au top !

Di qualità ma non rosso come in foto 👍

D.&.R. · 26 March 2023

Servizio Bolo impeccabile ! La bobina arriva come al solito in sottovuoto con la bustina di Silica, all'interno della scatola di cartone MADE IN CHINA troviamo una busta in plastica per riporre il filamento dopo l'uso (come fa Geeetech)Il filamento va benissimo e in linea con gli standard odierni, a 150mm/s si comporta bene e i risultati sono ottimi se ci si impegna a dovere con lo Slicer di turno per dare i giusti parametri ad una macchina che sia almeno qualitativamente sopra la media.Unico neo il colore che non è il classico rosso che useresti per un logo Ferrari o Milan per capirci.Comunque questo rosso mi è piaciuto e l'ho tenuto per altri progettiConsiglio con prezzo in sconto, buona stampa a tutti makers 👌

Yanıltıcı ürün

E.K. · 25 May 2024

Kutunun içinden sarı renk çıktı.Filamentin üstünde Pembe etiketi var.

Excellent

Y.C. · 27 April 2022

Très bon produit.La matière se charge facilement dans le crayon.Les couleurs sont sympa et bien variées.La matière donne de bon résultats.Je recommande ce produit